The smart home ecosystem has a new addition today! It is a highly intelligent home cleaning device improved with 2 in 1 Sweep and Mop. You can not only sweep the floor but also polish your floor with the mopping pad. Can you imagine that you can walk on the floor with bare feet in no need of worrying about the debris or other granules?
The same functions like the Xiaomi robotic vacuum:
The Laser Distance Sensor ( LDS ) scans its surroundings 360 degrees, 1800 times per second, to map out the interiors of your house. The three processors track its movements in real-time, and the Simultaneous Localization and Mapping ( SLAM ) algorithm calculates the most efficient route for cleaning. Using the Mi Home app, you can switch on and remotely control the robot, change cleaning modes and set schedules, Additionally, a powerful Nidec brushless DC motor, the main brush with adjustable height and a 5200mAh Li-ion battery for up to 2.5 hours of cleaning, attractive in price and quality, all these make it stand out of the market. Get the Roborock S50 Robot Vacuum and dirt will not stand a chance!
● 2 in 1 Sweep and Mop
- Double cleaning: sweep first and then mop the floor
- The filter is root-inspired when the mopping pad is served as leaves to control water flow like a living organism. It can mop the floor constantly for 45 - 60 minutes
● Intelligent Route Planning
Laser Distance Sensor ( LDS ) allows the robot to scan its surroundings at 360 degrees, 1800 times per second, with the Simultaneous Localization and Mapping algorithm to map out the interiors of your home and then provides real-time planning routes, edge cleaning followed by Z-shaped cleaning according to the surroundings
● Three-dimensional Vacuum Cleaning System
With its vacuum system, the robot empower your house a super cleaning like a tornado, with no dust, debris, granule, or any other wastes left, so clean and smooth that you can walk with bare feet on the floor
● APP Remote Control
Customized cleaning area is available, just one click to set wherever you wanna clean with the map in your phone
● 5200mAh Large Capacity Battery
The robot carries 5200mAh Li-ion battery which ensures 2.5 hours cleaning for a house of 250sq.m in full charge
● 2000Pa Super Suction
With a strong power, the robot absorbs all the debris, steel beads, soybeans, dust, millet or any other wastes all in a sudden
● Almighty Helper
- 2cm obstacle climbing
- 2mm Rubber Bumper
- 360 degrees LDS pressure sensor
- 4 anti-drop stair sensors
- 10mm laser edge sensor
- Auto power-off after leaving the floor
- Automatic self-recharging sensor
1. When in mopping, please do not use it on the rugs or carpets, especially for the shag, long-wool carpets, because it might scratch your precious carpet with water tank
2. The capacity of 2cm obstacle climbing may be declined when using water tank
Cleaner Types: Vacuum Cleaner
Feature: Mop,Remote Control,Self Charging
Self Recharging: Yes
Dust Box Capacity: 0.48L
Water Tank Capacity: 0.14L
Suction (pa): 2000pa
Power (W): 58W
Input Voltage (V): 100 - 240V
Current : 2.2A
Working Time: 2.5h
Battery Type: Li-ion
Battery Capacity: 5200mAh
Dimension and Weight
Product weight: 3.5000 kg
Package weight: 7.0000 kg
Product size (L x W x H): 35.30 x 35.00 x 9.65 cm / 13.9 x 13.78 x 3.8 inches
Package size (L x W x H): 56.60 x 43.30 x 15.20 cm / 22.28 x 17.05 x 5.98 inches
|Package Contents: 1 x Robot Vacuum, 1 x EU Plug Adapter, 1 x Charging Dock, 1 x Water Tank, 1 x Mopping Pad, 1 x English User Manual|
Q: What should I do when there is no water/too little water/too dried cloth for mopping?
A: Troubleshooting-1: check whether the water tank runs out of water; refill water if necessary.
Troubleshooting-2: check that the mopping cloth has been tightly installed. If the cloth is not tightly installed, the white filter assembly may not properly supply water to the mopping cloth. The filter may be blocked. Please immerse the filter assembly in citric acid or white vinegar; if the problem persists, replace the filter assembly.
Troubleshooting-3: please wet the mopping cloth before mopping and squeeze it dry before installation. If the mopping cloth is dirty, please clean it before reuse. Do not use non-original mopping cloth that may result in insufficient water flow.
Troubleshooting-4: please check that the water tank is installed in place.
Q: What should I do when there is high water flow/too much water/too wet cloth?
A: Troubleshooting-1: check whether the filter is not installed in place. If so, press the filter into place with your thumb.
Troubleshooting-2: check whether the O ring of the filter falls. If the O ring is lost, replace the filter assembly. Do not use non-original mopping cloth that may result in too high water flow.
Q: What should I do when failing to power the machine on?
A: This involves many possibilities: check whether it is resulted from battery low protection; connect it to the dock charger and put the machine onto the dock charger to check whether it can be normally started. The machine does not work in the temperature range of 0-40℃. Too high or low temperature will result in the condition that the battery is protected. Please check that the operating temperature is restored to 0-40℃ and kept for a certain period of time, and then try again.
Q: Why is recharge impossible for the machine after spot cleaning?
A: Spot cleaning requires re-generation of a map, and the previous map and the coordinate of the dock charger will be cleared which may result in failure to return to the dock charger. Therefore, please put the machine back onto the dock charger after spot cleaning.
Q: What should I do when the machine cannot automatically start working even if the timer cleaning is enabled?
A: Troubleshooting-1: check that the machine is powered on as the timer cleaning is ineffective when it is powered off
Troubleshooting-2: check that the battery capacity is higher than 20% as the timer cleaning is ineffective when the battery capacity is lower than 20%; it is recommended to keep the machine be seated on the dock charger and work in standby mode uninterruptedly
Troubleshooting-3: check that the cleaning timer is correctly set; for example, if it is set to "Once", the setting will not be effective any longer after being executed once, or if it is set to "Workday" and the current day is a weekend day, the timer cleaning will also be ineffective.
Q: Will long-term charging consume more power? Will overcharge shorten the service life of the battery?
A: Charging stops after the battery is full. The motherboard is powered directly from the dock charger and the battery is in standby mode and thus the battery performance will not be affected. The machine has very low power consumption (less than 3 W) when it is inoperative. To maintain the best performance of the battery, please try to keep the machine interfaced on the dock charger when it is left unused.
Q: What should I do when the machine works abnormally and always knock into a wall or furniture?
A: Very occasionally, the machine may have positioning deviation. Please pause the machine and put it back onto the dock charger and try again.
Q: What should I do when I get a message from the machine that the dock charger cannot be found and please move the machine to be close to the dock charger?
A: If no dock charger is available in the whole cleaning environment, the machine will return to the starting point after cleaning, and alert you with a message that the dock charger cannot be found and please move the machine to be close to the dock charger and try again.